top of page

Instruction For Use (IFU):

AquaGuard Pro® Series

Ultra filtration (Anti-Legionella / Bacteria) Under-Sink Filter

  • Model MWT-7400 /  MWT-7410

  • Q10137WH / Q10138WH

Aqua Guard Pro.png

AquaGuard Pro® Series

Ultra filtration (Anti-Legionella / Bacteria) Under-Sink Filter designed for bacteriological security and water purification.

The AquaGuard Pro is an ultrafiltration system engineered to reduce microbial contamination in water, including Legionella pneumophila, Nontuberculous Mycobacteria (NTM), E. coli, Salmonella, and other waterborne bacteria.
Featuring a high-performance 0.08 µm hollow-fiber membrane and antimicrobial housing, it is designed for installation under the sink or at the main water entry point in homes, commercial spaces, or institutional facilities. AquaGuard Pro supports long-term filtration efficiency in hygiene-sensitive environments.

Equipped with advanced ultra-filtration membranes in a pore size of 0.08 µm, our filters have been independently tested and certified to ASTM F838-2015ae, achieving Log 8 (99.999999%) bacterial reduction. In addition to this performance validation, our products are certified by NSF, IAPMO, and the U.S. EPA, and have been tested in accordance with ASHRAE performance criteria.

They also meet European safety and compliance standards, including the EU Drinking Water Directive (2020/2184) and DIN EN 16421, reflecting our commitment to global regulatory excellence.

Designed for compatibility with small spaces and featuring a click-connect system, the AquaGuard Pro is intended for one-time installation, with subsequent filter replacements achievable in just 5 seconds—no dismantling of the unit required. Simply swap out the filter effortlessly. For an enhanced experience, the installation of an on/off spigot is recommended.

Features:

  • 0.08 μm sterilizing grade hollow fiber membranes.

  • Exchangable Anti-Microbial Filter Cartridge.

  • Compatible with ADA-compliant pause adapter.

  • Robust pre-filtration cartridge.

  • In compliance with NSF P376, ASSE LEC 2011-2022, ASTM F838-2015ae1 / 2020 for Bactria and fungus reduction standards & EPA WaterSense

Benefits:

  • Retains microorganisms without volume restriction.

  • Waste reduction, and cost reduction with high performance.

  • Anti-microbial protection is embedded throughout the system.

  • Integrates with Legionella Water Management Plans.

  • Installed on the cold water source without affecting the water flow rate

Designed for under-sink installation to reduce exposure to waterborne bacteria at the point of consumption. Independently tested to significantly reduce microbial load, including Legionella pneumophila, E. coli, and Pseudomonas aeruginosa. Ideal for environments requiring consistently high water hygiene standards.

* Filter capacity is influenced by local water conditions, the concentration of microparticles (SDI), and pre-filtration. SDI is measured according to ASTM D4189-95 standards. It is recommended to replace the filter cartridge every 356 days for optimal performance.

AquaGuard Pro® Certification

  • In compliance with NSF P376, ASSE LEC 2011-2022, ASTM F838-2015ae1 / 2020 for Bactria and fungus reduction standards & EPA WaterSense

Copy of CE mark_edited.png

Surface Disinfection of the AquaGuard Pro® 

Regular wiping or spraying with these solutions will not affect the system's appearance or functionality, even in white. Please note that the system should remain connected throughout the cleaning process and should not be disconnected or dip at any time.

Recommended Cleaning Solutions:

  • Solution A: 70% denatured ethanol in water 

  • Solution B: 25 ppm active chlorine in water

  • Solution C: 0.5% quaternary ammonium solution

  • Solution D: 0.5% hypochlorous acid solution

COMPONENTS

AquaGuard Pro®

MWT-7400 /  MWT-7410

Q10137WH / Q10138WH​​

Diameter (nominal)

8.07" (20.5 cm)

Weight (nominal)

528 g / 18.62 oz

Flow Rate

There is no actual loss in the water flow.

EPA WaterSense Maximum Flow rate 1.8 gpm and 6.8 L/min

Temperature

Continuous influent temperature 60 °C (140 °F). Maximum influent temp. 70

°C (158 °F) for a total cumulative period of 30 mins over the life of each Filter Capsule

Max. Operating Pressure

360 psi (25 bar) at continuous 60 °C (140°F) influent temperature

Capacity

15,000 liters (3,963 gallons)

Main Materials of Construction

PP - Polypropylene

Pathogenic Reduction

99.999999% - Log 8

AquaGuard 4.png

WARNING

1_edited.png
2_edited.png
3_edited.png
4_edited.png

The following commonly used cleaning solutions are suitable for sanitizing and maintaining the Shower System during routine servicing. Regular wiping or spraying with these solutions will not affect the system's appearance or functionality, even in white. Please note that the system should remain connected throughout the cleaning process and should not be disconnected or dipped at any time.

This system is designed for use with water supplies that meet public water system standards or have been confirmed as microbiologically safe through routine testing. It has been tested to ensure protection against occasional accidental microbiological contamination of otherwise safe drinking water.

For optimal performance, this system requires all functional components to be installed in the correct order, following the provided installation and maintenance instructions. Failure to do so may result in the system not functioning as intended.

The system and installation must comply with all applicable state and local laws and regulations. For any questions or assistance, please contact our customer service team.

Gloves_edited.png

WARNING: Always wear protective gloves when installing or removing the filter. Direct contact with internal components can compromise hygiene and pose a contamination risk. Failure to use gloves may void warranty coverage.

About Mentor Water technologies

Mentor Water Technologies specializes in the development and manufacturing of premium water filtration systems. Engineered and produced in the Netherlands, our filters are designed to provide superior protection against harmful pathogens, including Legionella, E. Coli, and other waterborne contaminants. With an emphasis on innovation, quality, and stringent certification standards, Mentor Water Technologies offers reliable solutions for healthcare facilities, industries, and residential use. Our commitment to Dutch craftsmanship ensures that each product delivers outstanding performance, long-lasting durability, and peace of mind. Trusted by professionals worldwide, we continue to set the benchmark in water filtration technology.
 

 

Manufacturer: Benelux B.V, Korenbloemweg 79, Almere 1338XT, Netherlands +31 61 419 04 90

Warranty: Up to 18 months from delivery in sealed packaging, subject to proper storage and use per manufacturer guidelines.
 

bottom of page